Solutions for

Find a Rep or Distributor

Home /  EMC / 

EMC Positioners


  • 2090 Controller   |   Datasheet   |   Manual
    ETS-Lindgren's Model 2090 Positioning Controller allows you to synchronize simultaneous movement of two primary ETS-Lindgren devices (towers or turntables), and on/off operation of up to four auxiliary devices (LISNs, EUTs, etc.). Independent operation of primary devices can be performed manually, by either of the two front panel controls, or remotely by a separate GPIB address for each device. Fiber optic control lines eliminate RF interference that can be conducted through traditional wire cables.

Antenna Towers

  • 1052 Antenna Tower Positioner   |   Manual
    The ETS-Lindgren Model 1052 Portable Antenna Tower is useful for quick measurements, pre-scans, and anywhere a portable tower is needed.
  • 2171B Boresight Antenna Tower   |   Datasheet   |   Manual
    ETS-Lindgren's Model 2171B Antenna Tower meets ANSI C63.4 requirements for measurements above 1 GHz by keeping the antenna aimed at the EUT during the antenna’s ascent/ descent along the antenna mast. This is especially useful when high gain directional antennas like the log periodic are used. This new antenna tower is also designed with a reduced size base for better maneuverability in smaller chambers.
  • 2175 Antenna Tower   |   Datasheet   |   Manual
    ETS-Lindgren's Model 2175 MiniMast Antenna Tower maximizes available space in today’s compact chambers, while offering many features found on full-sized ETS-Lindgren towers. The mast section is made from one continuous piece of square fiberglass tubing. This construction improves stability during ascent and descent of the antenna. Nominal height is 4.6 m. Supporting up to 10 kg (22 lbs.) of weight, the MiniMast’s sturdy boom can be used with almost any EMC antenna.

Multi-Axis Positioner (MAPS)

RF Test Solutions

Single Axis Positioner

  • 2006 Single Axis Positioner   |   Datasheet
    ETS-Lindgren's Model 2006 Single Axis Positioner is designed to provide azimuth rotation of a test object. It is intended primarily as a basic solution for azimuth (polar) pattern measurements of passive and active devices.

Test Tables

  • Low Dielectric Table Models LDT-1.2, LDT-1.5   |   Datasheet
    ETS-Lindgren’s Low Dielectric Tables (LDT) are lightweight, portable test tables, constructed with materials selected for their low dielectric properties. The construction materials for the EUT's support surface have a dielectric constant of <3.0, with each table's support structures having a dielectric constant of <1.03. The result is a table having virtually no influence on radiated emissions measurements, especially above 1 GHz, where frequencies are affected most.



  • 1062-1.2 Turntables
    ETS-Lindgren's Model 1062-1.2 is a low profile, manually operated, wood topped turntable designed for pre-scan measurements.
  • 2165 Turntable   |   Manual
    ETS-Lindgren's Model 2165 LoProTM Turntable is ideal for today's EMC test applications where height is a concern and installation options may be limited.
  • 2181 Turntable   |   Manual
    ETS-Lindgren's Classic Series Model 2181 turntables have a long legacy of durability and trouble free operation since the 1980's.
  • 2187 Turntable   |   Manual
    ETS-Lindgren's Value Series Model 2187 turntables are designed for applications requiring a mid-sized turntable with reasonable weight load requirements.
  • 2188 Turntable   |   Manual
    ETS-Lindgren 2188 EuroPro™ Turntable family is ideal for today’s EMC test applications where height is a concern and installation options may be limited.
Tel +1.512.531.6400 Tel +358.2.8383.300 Tel +44(0)1438.730700 Tel + Tel +8610.8275.5086 Tel+ 81.3.3813.7100
Fax +1.512.531.6500 Fax +358.2.8651.233 Fax +44(0)1438.730751 Fax + Fax +8610.8275.5537 Fax +81.3.3813.8068

Information presented is subject to change as product enhancements are made. Contact ETS-Lindgren Sales Department for current specification.