Solutions for


Find a Rep or Distributor

Home /  Categories /  Test Enclosures / 

5247 Shielded Test Cell Enclosure

5247 Shielded Test Cell Enclosure

The ETS-Lindgren Model 5247 is a self-contained portable enclosure for making wireless device over the- air performance measurements. The unit can be used for design verification, pre-certification, and production line measurement applications. Rolling casters allow the unit to be readily moved between locations.
Ask a Question Ask a Question

Print Version Print Version
5247 Datasheet Product Datasheet

Key Features

  • Roll-About Casters
  • Portable RF Shielded Enclosure for OTA measurements
  • >80 dB Typical RF Isolation
  • RF Absorber Lined
  • Dual Polarized Horn Antenna
  • 700 MHz - 10 GHz Frequency Range
  • Linear & Circular Polarization
  • Connector Panel
  • 1 SMA Connector
  • 3 Type N Connectors
  • Filtered D-sub 25 Pin Connector
  • Six-Line, Fiber Optic Feed-Through
  • Dual Latching RF Gasketed Door
  • Integrated System Configurations Available

Description

RF Shielding

The ETS-Lindgren Model 5247 is constructed with the same RF shielding and shielded door technology used in the construction of our larger, full certification wireless test chambers. The RF shielded door uses compressible finger stock in a “knife edge” configuration. Two latch points with a single point handle provide secure sealing and one-hand operation. Typical RF isolation of both the shielding and door is greater than 80 dB.

Anechoic Absorber

The RF anechoic absorber used in the Model 5247 is performance optimized for the frequencies of interest. The absorber limits reflections and moding, contributing to more accurate, repeatable measurements. Tapered wedges line the walls, pyramidal absorber is used on the floor, and lossy foam lines the antenna.

Dual Polarized Horn Antenna

The ETS-Lindgren Model 5247 is equipped with an EMCO brand, dual polarized horn antenna. The standard included antenna can make both linear and circular measurements over the frequency range of 700 MHz to 6 GHz. (Optional hybrid required for circular measurements.) Typical frequency response is flat from 2 GHz through 6 GHz.

The antenna is mounted on quick-change removable access panel at the top or “ceiling” of the enclosure. The antenna can be quickly interchanged with another antenna of a different frequency, etc., as needed.

Connector, Antenna and Access Panels

A populated connector panel (bulkhead feed through) is included with the Model 5247. The panel includes; one SMA connector, three Type N connectors, one filtered D-sub 25-pin connector, a six-line fiber optic feed-through, and one ground stud. A USB fiber optic media converter with a two-port hub (requires 110/220 VAC/5A supplied) is optional.

A quick-change antenna mounting panel (with a pre-mounted antenna) is included.

APPLICATIONS

Typical applications for the Model 5247 include radiated power (TX) and sensitivity (RX) measurements made during design verification, pre-certification, and in-line testing functions.

USA FINLAND UK FRANCE CHINA JAPAN ONLINE
Tel +1.512.531.6400 Tel +358.2.8383.300 Tel +44(0)1438.730700 Tel +33.1.48.65.34.03 Tel +8610.8275.5086 Tel+ 81.3.3813.7100 info@ets-lindgren.com
Fax +1.512.531.6500 Fax +358.2.8651.233 Fax +44(0)1438.730751 Fax +33.1.48.65.43.69 Fax +8610.8275.5537 Fax +81.3.3813.8068 www.ets-lindgren.com

Information presented is subject to change as product enhancements are made. Contact ETS-Lindgren Sales Department for current specification.